- Home
- Appliances
- Washer repair
Washer Repair — Greater Phoenix
A washer that stops mid-cycle, won't drain, or leaks onto the garage floor is the kind of problem that gets worse the longer it waits. Call and we'll connect you with an independent appliance repair company that works on washers in your part of the Valley.
A person answers Mon-Fri 9am-5pm. Outside those hours, leave a message and a local company calls you back.
Answered by an independent Phoenix-area appliance repair company. Not a call center.
Washer problems
- Won't drain or spin
- Won't fill, or fills and stops
- Leaking from underneath or the door
- Loud banging or walking across the floor
- Error codes on Samsung, LG, Whirlpool and GE front-loaders
- Door or lid lock won't release
- Top-loader agitator not moving
What's your washer doing?
Pick the symptom for the likely cause, what to check first, and when it needs a technician.
4CSamsung washer 4C code: what it means and how to fix it
A 4C code, shown as 4E on older models, means the washer didn't get the water it expected inside the time the control…
Read the fix →LG washerOELG washer OE code: what it means and how to fix it
OE means the washer did not empty the water within the time it expected, so it halted the cycle and flagged a drain…
Read the fix →LG washerUEUE LG washer code: what it means and how to fix it
UE (you may see it as uE or Ub) means the washer sensed an unbalanced load and stopped the spin to protect itself. Nine…
Read the fix →GE washerGE washer not draining: what it means and how to fix it
A GE washer that won't drain has either a blockage between the tub and the house standpipe, or a drain pump that's…
Read the fix →Samsung washerSCSamsung washer SC code: what it means and how to fix it
SC, and its newer form 5C, means the washer couldn't empty the tub in the time the control expected, so it halted the…
Read the fix →GE washerGE washer not spinning: what it means and how to fix it
A GE washer that won't spin is almost always blocked by a safety condition rather than a dead motor, usually a lid…
Read the fix →LG washerIELG washer code IE: what it means and how to fix it
IE (water inlet error) means the washer didn't reach its target water level within the time the control allows. Most of…
Read the fix →LG washerLELG washer code LE: what it means and how to fix it
LE is a locked motor error, meaning the control told the drum to spin and the motor didn't turn the way it expected. The…
Read the fix →Samsung washerU6U6 code on a Samsung washer: what it means and what to do
U6 means the control board sensed the drum was off balance during spin and stopped it to protect itself. Nine times out…
Read the fix →Repair it or replace it?
The rule most technicians use: if the repair would cost more than half of a comparable new unit and the appliance is past two-thirds of its typical life, replace it. A good local company will say so on the phone.
In the Valley, heat is the variable people miss. Garage laundry rooms and second refrigerators run at 110°F or more all summer, which shortens compressor, pump and belt life by years.
Hatched span is the upper end you shouldn't count on in an uncooled garage. Ranges are the manufacturer figures technicians work from, not a promise about your unit.
Washer repair by brand
Brand names identify the appliance you own and do not imply any affiliation with the manufacturer.
Washer repair by cityCommon questions about appliance repair in Phoenix
Is it worth repairing a washer or should I replace it?
Most repair companies will tell you on the phone whether the symptom you describe is usually a small part (a drain pump, lid switch or belt) or something major like a bearing or control board. If the machine is under about eight years old and the fault is a common part, repair is normally the sensible route.
Do repair companies in the Phoenix area work on garage-installed washers?
Yes. Garage laundry is common in Mesa, Gilbert and Chandler homes, and the heat there is hard on pumps and electronics. Mention that the machine is in the garage when you call so the technician plans for it.
How soon can someone come out?
That depends on the company and the day. When you call, you'll be connected directly with a local repair company and they'll tell you their next available slot.
What does it cost to have a washer looked at?
Each company sets its own service-call and repair rates. Ask for their diagnostic fee and whether it's applied to the repair before you book.
Talk to a local appliance repair company, not a bot
One call connects you with an independent repair company in your part of the Valley. Mon-Fri 9am-5pm.